HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 10-12 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms a flat and flush seating area

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  the HappyLounge is then approx. the same height as the bench seat

• There is usually no double floor in the dinette area of your motorhome: this means that you have a step approx. 7 – 15 cm high from the dinette into the driver’s cab. The HappyLounge supports stand on the step in the cockpit.

Example photos in the Challenger (and Chausson sister model):

to the picture gallery >>

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 10-12 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms a flat and flush seating area

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  the HappyLounge is then approx. the same height as the bench seat

• There is usually no double floor in the dinette area of your motorhome: this means that you have a step approx. 7 – 15 cm high from the dinette into the driver’s cab. The HappyLounge supports stand on the step in the cockpit.

Example photos in the Challenger Slim (and Chausson sister model):

to the picture gallery >>

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  – in the lowest position, the cab seats are usually approx. 10-12 cm lower than the adjacent side seating group – this means that the HappyLounge and your side seating group usually form a level and flush seating area
  – the HappyLounge closes the gap between the driver’s cabin seats and the side seating group flush with the vehicle partition (B-pillar)
  – it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the partition wall.

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  – the HappyLounge is then approx. the same height as the bench seat
  – the HappyLounge usually protrudes approx. 10 cm into the sliding door opening. TIP: You can change this and gain spaceby setting the cab seats in a staggered position rather than in one line: move the passenger seat closer to the cockpit than the driver’s seat. The HappyLounge is then positioned at an angle in the cockpit when viewed from above and then only protrudes approx. 2-3 cm into the sliding door opening.
  

• Your motorhome has a double floor in the dinette area or throughout the entire motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps).

Example photos in the LMC Innovan:

Example photos in the Bürstner Lineo van:
(the HappyLounge supports are not fitted in these photos):

to the picture gallery >>

HappyLounge S-FD with approx. 56 cm seat depth

to the picture gallery >>

• the HappyLounge has a soft foam comfort structure of up to 14 cm
• it lies on your cab seats turned into the living area
• it only builds up to a height of approx. 4-5 cm on the seat
• it also protrudes approx. 6-8 cm forwards over the seat (= seat protrusion approx. 6-8 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• It is therefore independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the partition wall.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. the same height as the adjacent side seating group – the HappyLounge therefore protrudes approx. 4-5 cm above the side seating group (seat surface is max. 4-5 cm higher)

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  the HappyLounge is then approx. 4-5 cm higher than the bench seat

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

—–
IMPORTANT NOTE ON THE SEAT SPACING IN YOUR MOTORHOME
The seat spacing of the driver’s cabin seats (standard pilot seats with 2 armrests each) is usually approx. 30 cm (+/- 2 cm) – for smaller or larger seat spacings or if your seats only have one armrest, please contact us and we will check an individual customization.

——

Example photos in the Eura Mobil:

Example photos in the Bürstner:

to the picture gallery >>

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

– Vehicles with the extra-high technical double floor that we know and have tested so far: Mobilvetta Krosser, Roller Team Granduca and Frankia 740-2012

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 10-12 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms a flat and flush seating area

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  the HappyLounge is then approx. the same height as the bench seat

• In your motorhome, there is an extra-high (20 cm) double technical floor in the dinette area or throughout the motorhome: your driver’s cab floor is therefore approx. 10 cm below the body floor (sloping slope from the dinette into the driver’s cab).

—–
IMPORTANT NOTE ON THE SEAT SPACING IN YOUR MOTORHOME
The seat spacing of the driver’s cabin seats (standard pilot seats with 2 armrests each) is usually approx. 30 cm (+/- 2 cm) – for smaller or larger seat spacings or if your seats only have one armrest, please contact us and we will check an individual customization.

——

Sample photos in the Roller Team:

Example photos in Frankia:

to the picture gallery >>

HappyLounge S-FD with approx. 56 cm seat depth

to the picture gallery >>

• the HappyLounge has a soft foam comfort structure of up to 14 cm
• it lies on your cab seats turned into the living area
• it only builds up to a height of approx. 4-5 cm on the seat
• it also protrudes approx. 6-8 cm forwards over the seat (= seat protrusion approx. 6-8 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• It is therefore independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the partition wall.
• In your motorhome, the dinette area or the floor in the entire motorhome is lower than the driver’s cab floor. This means that the cab floor with the seats is above the body floor and you have a step up into the cab

• Motorhomes with side seating group (dinette):
  – In the lowest position, the cab seats are usually approx. 5-12 cm higher than the adjacent side seating group (your cab seats always protrude approx. 5-12 cm above the side seating group): They cannot be adjusted lower and cannot be brought to a required low position to reach the height level of the side seating group and form a level seating surface.
  – The HappyLounge therefore protrudes upwards by a further approx. 4-5 cm above the side seating group (the seat is a maximum of another 4-5 cm higher, which means a total height difference of approx. 9-16 cm between the side seating group and HappyLounge(there is a step of 9-16 cm between the side seating group and HappyLounge). Unfortunately, we can’t change this either.
  But we have another idea for you! – See below.

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  There is no visual height comparison as there is no adjacent seating group.

—–
IMPORTANT NOTE ON THE SEAT SPACING IN YOUR MOTORHOME
The seat spacing of the driver’s cabin seats (standard pilot seats with 2 armrests each) is usually approx. 30 cm (+/- 2 cm) – for smaller or larger seat spacings or if your seats only have one armrest, please contact us and we will check an individual customization.

——

Example photos in the Challenger (and Chausson sister model):

IDEA FOR YOU:

Raise the height level of the dinette
The height difference between the side seating group and the HappyLounge can be reduced by a few centimeters by placing foam panels underneath. Again, this requires sufficient space and legroom between the lower edge of the table and the seat as well as a seat height that is still comfortable for you (see information on taking measurements in the section FAQ – Questions and answers here >> )

to the picture gallery >>

YOU HAVE THE CHOICE
choose your favorite from these 2 HappyLounge variants:

POSSIBILITY 1: HappyLounge variant S-FD with approx. 56 cm seat depth – see description below

POSSIBILITY 2: HappyLounge variant LIGHT ROCK’N’ROLL with approx. 50 cm seat depth – see separate menu item panel van >>

———————————–

DESCRIPTION FOR OPTION 1: HappyLounge variant S-FD with approx. 56 cm seat depth

to the picture gallery >>

• the HappyLounge has a soft foam comfort structure of up to 14 cm
• it lies on your cab seats turned into the living area
• it only builds up to a height of approx. 4-5 cm on the seat
• it also protrudes approx. 6-8 cm forwards over the seat (= seat protrusion approx. 6-8 cm)

• Motorhomes with side seating group (dinette):
  In the lowest position, the driver’s cabin seats are usually approx. the same height or slightly higher than the adjacent side seating group – so the HappyLounge protrudes upwards by a further approx. 4-5 cm above the side seating group (seat surface is at least another 4-5 cm higher).

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  – depending on the driver’s seat height, the HappyLounge is at least 4-5 cm higher than the bench seat
  – the HappyLounge usually protrudes approx. 10 cm into the sliding door opening

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

• GREAT TIP: Raise your table with little effort!
  We also have a great accessory set for you, with which you can easily raise your table!
  

—–
IMPORTANT NOTE ON THE SEAT SPACING IN YOUR MOTORHOME
The seat spacing of the driver’s cabin seats (standard pilot seats with 2 armrests each) is usually approx. 30 cm (+/- 2 cm) – for smaller or larger seat spacings or if your seats only have one armrest, please contact us and we will check an individual customization.

——

Example photos in the Challenger Van V210:

Sample photos in the Challenger Van F&S Family&Sport:

Example photos in the Eura Mobil Van V635EB:

to the picture gallery >>

– MAN TGE almost identical to VW Crafter –

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 7-10 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms an almost flat and flush seating surface (or protrudes max. 3-4 cm above it)

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  the HappyLounge is then approx. the same height as the bench seat (or protrudes max. 3-4 cm above it)

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in the Knaus:

Example photos in the Knaus 700 LF Vansation:

to the picture gallery >>

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 7-10 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms an almost flat and flush seating surface (or protrudes max. 3-4 cm above it)
  

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  the HappyLounge is then approx. the same height as the bench seat (or protrudes max. 3-4 cm above it)
  

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in the VW Crafter Gran California:

Example photo in the VW Crafter Gran California – self-conversion –
(the HappyLounge supports are not fitted in the photo):

to the picture gallery >>

HappyLounge S-FD with approx. 56 cm seat depth

to the picture gallery >>

• the HappyLounge has a soft foam comfort structure of up to 14 cm
• it lies on your cab seats turned into the living area
• it only builds up to a height of approx. 4-5 cm on the seat
• it also protrudes approx. 6-8 cm forwards over the seat (= seat protrusion approx. 6-8 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  – in the lowest position, the cab seats are usually approx. the same height as the adjacent side seating group: the HappyLounge therefore protrudes upwards by approx. 4-5 cm above the side seating group (seat surface is max. 4-5 cm higher)
  or
  – in the lowest position, the cab seats are approx. 3-5 cm lower than the adjacent side seating group: the HappyLounge and your side seating group therefore form an almost level and flush seat surface (or protrude a maximum of 2-3 cm above it)
  

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  the HappyLounge is approx. the same height or up to approx. 4-5 cm higher than the bench seat, depending on the height of the bench seat

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in the Hymer:

to the picture gallery >>

– These Aguti special seats are available as an option from many motorhome manufacturers. In Eura Mobil vehicles on Merede’s Sprinter, for example, they are fitted as standard.

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 7-10 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms an almost flat and flush seating surface (or protrudes max. 3-4 cm above it)
  

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  the HappyLounge is then approx. the same height as the bench seat (or protrudes max. 3-4 cm above it)
  

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in the Eura Mobil:

to the picture gallery >>

– These special Isringhausen seats (Isri) are available as an option from many motorhome manufacturers. Some of them are already installed as standard, e.g. in some Frankia –

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 10-12 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms a flat and flush seating area

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  the HappyLounge is then approx. the same height as the bench seat

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in Frankia:

to the picture gallery >>

HappyLounge variant S-FD with approx. 56 cm seat depth

to the picture gallery >>

• the HappyLounge has a soft foam comfort structure of up to 14 cm
• it lies on your cab seats turned into the living area
• it only builds up to a height of approx. 4-5 cm on the seat
• it also protrudes approx. 6-8 cm forwards over the seat (= seat protrusion approx. 6-8 cm)

• Motorhomes with side seating group (dinette):
  – in the lowest position, the cab seats are approx. 3-5 cm lower than the adjacent side seating group: this means that the HappyLounge forms an almost flat and flush seating area with your side seating group (or protrudes max. 2-3 cm beyond it)
  – the HappyLounge closes the gap between the cab seats and the side seating group flush with the vehicle partition (B-pillar)
  – it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the partition wall.

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  – depending on the height of the bench seat, the HappyLounge is approx. the same height as the bench seat (or protrudes max. 2-3 cm above it)
  – the HappyLounge usually protrudes approx. 6-8 cm into the sliding door opening

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Example photos in Hymer Free Blue:

to the picture gallery >>

– These special Isringhausen seats (Isri) are available as an option from many motorhome manufacturers. Some of them are already fitted as standard, e.g. in some La Strada –

HappyLounge S with approx. 60 cm seat depth

to the picture gallery >>

• the HappyLounge has an approx. 10 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 10 cm on the seat
• it also protrudes approx. 10 cm forwards over the seat (= seat protrusion approx. 10 cm)
• it closes the gap between the cab seats and the side seating group flush with the on-board partition (B-pillar)
• it is independent of cabinets, doors, dinettes, etc. installed in the vehicle adjacent to the on-board partition.

• Motorhomes with side seating group (dinette):
  in the lowest position, the driver’s cabin seats are usually approx. 10-12 cm lower than the adjacent side seating group – so the HappyLounge together with your side seating group usually forms a flat and flush seating area

• Motorhomes without side seating group (dinette) – only with bench seat opposite:
  – the HappyLounge is then approx. the same height as the bench seat
  – it can also protrude approx. 6-8 cm into the sliding door opening

• In your motorhome, there is a raised floor structure or double floor in the dinette area or throughout the motorhome: this means you have a continuous floor from the dinette to the driver’s cab (no steps)

Sample photos at La Strada:

to the picture gallery >>

— on Fiat Ducato, Citroen Jumper, Peugeot Boxer, Opel Movano PSA —

YOU HAVE THE CHOICE
choose your favorite from these 2 HappyLounge variants:

————————————————-

POSSIBILITY 1: HappyLounge variants S and S-FD for semi-integrated vehicles (also suitable for panel vans) – see previous separate menu items: back to previous menu item / vehicle selection >>

OPTION 2: HappyLounge variant LIGHT ROCK’N’ROLL for panel vans with approx. 50 cm seat depth (for the time being only for Fiat Ducato and Stellantis sister models) – see description here below

—————————————-

DESCRIPTION FOR OPTION 2: HappyLounge variant LIGHT ROCK’N’ROLL with approx. 50 cm seat depth (only recommended for panel vans)

to the picture gallery >>

• the HappyLounge has a 7 cm soft foam core
• it lies on your cab seats turned into the living area
• it builds up to a height of approx. 7 cm on the seat
• it also protrudes approx. 5-8 cm forwards over the seat (= seat protrusion approx. 5-8 cm)

• Motorhomes with side seating group (dinette):
  In the lowest position, the driver’s cabin seats are usually approx. the same height or slightly higher than the adjacent side seating group – so the HappyLounge protrudes upwards by a further approx. 7 cm above the side seating group (seat surface is at least another 7 cm higher)

• Motorhomes without side seating group (dinette) – only with opposite bench seat:
  – depending on the driver’s seat height, the HappyLounge is at least 7 cm higher than the bench seat
  – the HappyLounge protrudes approx. 5-8 cm into the sliding door opening

• GREAT TIP: Raise your table with little effort!
  We also have a great accessory set for you, with which you can easily raise your table!
  

• Stow away: the HappyLounge LIGHT ROCK’N’ROLL can be rolled up compactly*, alternatively laid flat or used as a backrest on the rear bed
  (*The crinkle look created after rolling up will smooth out after a while)

Example photo in the Challenger Van V114 Break Edition 2024

Example photos in the Challenger Van V217:

Example photos in the Carado 339V 2021 on Citroen Jumper (in the picture: custom-made product with pockets sewn onto the panel)

Storage: compactly rolled, alternatively laid flat on the rear bed or as a backrest

to the picture gallery >>

Fully integrated motorhomes in particular are perfect for the HappyLounge. You can use almost the entire width of the vehicle and therefore not only have a huge sofa area, but also an additional bed or a lounger almost the length of a comfortable normal bed.

HAPPYLOUNGE i-FD-EM (2-part seat, with 2 back cushions 70×50 and 2 back cushions 60×60)
suitable for Eura Mobil fully integrated Integra / Integra Line on Fiat Ducato:

HAPPYLOUNGE i-MB-EM (3-part seat, with 2 back cushions 70×50 and 2 back cushions 60×60)
suitable for Eura Mobil fully integrated Integra Line GT on Mercedes Sprinter:

First photos
Here you can see the first photos of our HappyLounge version in the fully integrated motorhome. The fold-down bed can also be used perfectly with the HappyLounge set up underneath. The HappyLounge back cushions even provide a comfortable place to lean against while reading or watching TV in the fold-down bed…

Eura Mobil Integra Line on Fiat Ducato:

to the picture gallery >>

Further models are already in development
We are constantly on the road for you, measuring and testing motorhomes so that we can expand our portfolio.
We are also already developing further HappyLounge variants for fully integrated motorhomes.

in the picture gallery >>

Your HappyLounge makes this easy:

Quickly assembled – compactly stowed away.

Very light, extremely stable and resilient.

Hard-wearing, easy-care and durable.

Strong: for extreme resilience. Gentle: for maximum protection of your cab seats

The HappyLounge becomes your favorite comfortable seat and at the same time a gentle seat protector: soft seat cushions made of comfortable foam protect and preserve your cab seats permanently and to the maximum. At the same time, cleverly integrated invisible stabilizing elements, supports and Velcro connections in the right places ensure a secure hold and high load-bearing capacity.

The HappyLounge® upholstery fabric is much more than just an ordinary upholstery fabric. Our ChellTEXX is a double-layered high-tech microfiber velour that combines comfort, durability and ease of care at the highest level.

For maximum suitability for everyday use in your camper.

*****

Special properties and special benefits:

– Soft Touch: soft and velvety with a suede look and feel
– very robust and hard-wearing
– easy-care
– with anti-stain finish (impregnation)
– dirt, moisture/liquid-repellent
– sweat-resistant
– breathable
– durable
– double-layered for dimensional stability

*****

Safety is not an extra for us. It’s the basis for your added value.
Our HappyLounge® ChellTEXX upholstery fabric with 70,000 abrasion cycles reliably meets all relevant standards. It also complies with the

OEKO TEX STANDARD 100

*****

Our ChellTEXX has also been tested by the public testing center for the textile industry:

– Wash fastness according to DIN EN ISO 105-C06
– Water fastness according to DIN EN ISO 105-E01
– Perspiration fastness according to DIN EN ISO 105-E04
– Water stain fastness according to DIN EN ISO 105-E07
*****and has achieved the maximum number of points in each case*****

*****

CARE

• Hand wash – only wash gently by hand

• Do not bleach – do not use bleach

• Do not tumble dry

• Do not dry clean

• Do not iron

Cleaning and care instructions
Thanks to the stain protection finish (impregnation), liquids can simply be soaked up or wiped off with a cloth if treated immediately. Stains can be cleaned with warm water and/or a little soap. To do this, apply water (or the soap solution for stubborn stains) to a clean (white) cotton cloth and work in a circular motion from the outside to the inside. If any water remains after cleaning, moisten the entire upholstery again evenly.

All covers have a zipper and are therefore removable and washable. We will be happy to help you put them back on.

Washing has a negative effect on the special stain protection finish (impregnation) and causes it to disappear more quickly. However, you can re-impregnate at any time with a skin-friendly, gentle impregnation spray!

Please measure in your mobile home. Try out and test the space conditions, e.g. with your own cushions/blankets/upholstery.

• Do you still have enough space and legroom between the bottom edge of the table and the HappyLounge seat?
  Tip: raise your table by approx. 4 cm (we can supply you with the table raising kit)

• Do you still have enough space and legroom between the opposite bench seat and the HappyLounge seat? (for vehicles with a bench seat opposite)
  Tip: raise your table by approx. 4 cm (we can supply you with the set for raising the table)
  

• Is the seat height with the HappyLounge comfortable for you?
  (if your vehicle seats are very high even in the lowest position or if they cannot be adjusted to the lowest position (e.g. because of the body battery underneath), then you may not be able to put your feet on the floor)

• Is there space in front of the cab seats to set up the supports?
  (here, too, the installation of batteries, inverters, fire extinguishers, etc. could hinder the installation of the supports)

Example photos in the panel van / van

• Please set the driver’s cabin seats turned into the living area to the lowest position or 10 cm lower than the adjacent seating group / opposite bench seat:

a) Fiat Ducato/Peugeot Boxer/Citroën Jumper, MAN TGE, Mercedes Sprinter, VW Crafter:
Seating surfaces sloping backwards at an angle (lever at the side)

b) Ford Transit:
Adjust the seats to a horizontal position (turn the wheel on the side forwards)

• Slide the seats all the way back to the cockpit or so far back that the HappyLounge is flush with the adjacent seating area

• the inclination of the vehicle seat backrests brings you into a comfortable position (the steering wheel is the limiting factor here)

• If this option is available in your vehicle: Lower the steering wheel into the cockpit (push it in) and set it to the lowest position

HAPPYLOUNGE S – for semi-integrated motorhomes

– Width: cockpit width
– 60 cm seat depth
– 3-part seat
– 10 cm soft foam core | builds up to approx. 10 cm height on the seat
– 5 metal supports
– 3 back cushions 50×70 cm each

WEIGHT without
Packaging for storage
(without large-capacity bags, individual bags and covers for support legs):
approx. 13-14 kg (depending on support leg lengths and required accessories depending on base vehicle)

WEIGHT with
packaging for storage
(with large-capacity bags, individual bags and covers for support legs):
approx. 15-16 kg (depending on support leg lengths and required accessories depending on base vehicle)

PACKING DIMENSIONS:
2 bags with the cushions: 60x60x35cm and 70x50x30cm
With vacuum compression, the HappyLounge also fits in a single bag (60x70x40cm)

UNDERWAY STUDIES – our TIP:

Back cushions as a leaning option at the head end of the rear bed

Seat cushions (and back cushions) complete on seating group:

In this photo, ALL 6 cushions of the HappyLounge size S are lying on the side seat bench in the motorhome (driver’s side):
– 2 seat cushions lying on the seat
– and 1 seat cushion + 3 back cushions = 4 individual cushions in a row (2 rows) as backrests

Another great TIP:

Store your HappyLounge in ultra-sturdy storage nets storage nets from BIRKLE in Constance. These can be placed in the garage, under the hinged bed base, etc. More information >>

Click here for more storage tips and ideas (click on the image >>

to the picture gallery >>

HAPPYLOUNGE S-FD and S-MB for semi-integrated motorhomes (but also suitable for panel vans)

– Width: Cockpit width
– 56 cm seat depth
– 2-piece seat
– up to 14-cm soft foam comfort construction | still only builds up approx. 4-5 cm height on the seat!
– 4 metal supports
– 3 back cushions 50×70 cm each

WEIGHT without
packaging for storage
(without large-capacity bags, individual bags and covers for support legs):
approx. 14-15 kg (depending on support leg lengths and required accessories depending on base vehicle)

WEIGHT with
packaging for storage
(with large-capacity bags, individual bags and covers for support legs):
approx. 16-17 kg (depending on support leg lengths and required accessories depending on base vehicle)

PACKING DIMENSIONS:
2 bags with the cushions: 85x56x30cm and 70x50x30cm
With vacuum compression, the HappyLounge also fits in a single bag (85x56x40cm)

UNDERWAY STUDIES – our TIP:

Back cushions as a leaning option at the head end of the rear bed

Seat cushions (and back cushions) complete on seating group:

In this photo, ALL 5 cushions of the HappyLounge size S-FD are lying on the side seat bench in the motorhome (driver’s side):
– 2 seat cushions lying on the seat
– 3 back cushions standing one behind the other as backrests

Another great TIP:

Store your HappyLounge in ultra-sturdy storage nets storage nets from BIRKLE in Constance. These can be placed in the garage, under the hinged bed base, etc. More information >>

Click here for more storage tips and ideas (click on the image >>

to the picture gallery >>

HAPPYLOUNGE LIGHT Rock’n’Roll – for panel vans

– Width: Cockpit width
– 50 cm seat depth
– 1-piece seat
– 7 cm soft foam core | builds up to a height of approx. 7 cm on the seat
– 2 metal supports
– 1 large back cushion 60×60 cm

WEIGHT without
packaging for storage
(without large capacity bag, individual bags and covers for support feet):
approx. 5.5 kg + cushion 1 kg = 6.5 kg

WEIGHT with
packaging for storage
(with large-capacity bag, individual bags and covers for support feet):
approx. 7.5 kg

PACKING DIMENSIONS:
1 bag 35x50x60cm + cushion 60x60x15cm (cushion also fits in the bag)

Stow away on the go – our TIP:
rolled up compactly* or flat / as a backrest on the rear bed

*see instructions on how to roll up the HappyLounge LIGHT Rock’n’Roll correctly in the FAQs Shipping and stowage options

Another great TIP:

Store your HappyLounge in ultra-sturdy storage nets storage nets from BIRKLE in Constance. These can be placed in the garage, under the hinged bed base, etc. More information >>

—–

to the picture gallery >>

The HappyLounge LIGHT Rock’n’Roll – for panel vans – is delivered rolled up compactly.

Stow away: You can roll up your HappyLounge LIGHT Rock’n’Roll compactly and conveniently when you’re on the move. It can be rolled up*, alternatively laid flat or used as a backrest on the rear bed
*Thecrinkle look created after rolling up will smooth out after a while — see instructions on how to roll up correctly in the product information supplied

Another great TIP:

Store your HappyLounge in ultra-sturdy storage nets storage nets from BIRKLE in Constance. These can be placed in the garage, under the hinged bed base, etc. More information >>

TIPS, IDEAS AND INFORMATION ON STORAGE OPTIONS ON THE GO

Have you already found a clever way to store your HappyLounge on the go?

Great TIP:

Store your HappyLounge in ultra-sturdy storage nets storage nets from BIRKLE in Constance. These can be placed in the garage, under the hinged bed base, etc. More information >>

Click here for lots more storage tips and ideas (click on the image) >>

Lightweight wooden stabilizing elements incorporated into the foam seat cushions ensure resilience and stability. The seat is also supported and fixed in place by adaptable metal support feet and the Velcro fastening system.

LIGHTWEIGHT WOOD ELEMENTS

• Extremely stable due to special multilayer structure

• Proven in vehicle construction, shipbuilding, etc.

• Made from sustainably grown light wood

• Wooden elements have a special shape

• The wooden elements are only incorporated into the upholstery in areas that do not rest on the seats:
  foam seat shells and the covers of your vehicle seats are thus protected and given maximum protection

Each seating element of the HappyLounge can be loaded with up to 130 kg.

The ingenious Velcro fastening system ensures stability, modular handling and the perfect look of your HappyLounge.

• Velcro fasteners in the right places ensure that the seat cushions are firmly attached to each other: the entire seat surface made up of individual cushion elements is thus firmly connected to each other
  

• so nothing can slip, wobble or rock
  

• the edges of the HappyLounge always remain in position and provide a visually appealing and comfortable flat seating surface at all times

• Sewn-on Velcro covers guarantee the all-round soft feel of the HappyLounge and maximum protection for your textiles and furniture

• the modular handling with the individual upholstery elements enables quick and easy assembly and disassembly as well as space-saving storage options
  

IN THE SCOPE OF DELIVERY OF YOUR HAPPYLOUNGE YOU WILL FIND:

• Seat/reclining upholstery (1-piece, 2-piece or 3-piece, depending on vehicle/version) – each in cockpit width
• XL storage bag for seat/lying cushions

• 3 back cushions 70×50 for semi-integrated versions // 2 back cushions 70×50 and 2 large back cushions 60×60 for fully integrated versions
• XL storage bag for back cushions and pillows
• *EXCEPTION: only 1 back cushion 60×60 is included with the LIGHT Rock’n’Roll version (without extra bag)
• Optional additional cushions and pillows on request

• Support feet (2, 3, 4 or 5… depending on vehicle/version)
• Edge protection for storing the support feet
• Storage bag (scratch protection) for support feet
  

• Product information and quick assembly instructions

• Depending on the vehicle/model, the seat wedges and a fastening strap are also included (the HappyLounge LIGHT Rock’n’Roll also includes several straps)

An overview of all current prices and model variants of the HappyLounge can be found here:

https://happylounge.camp/#lieferzeiten

The current delivery times for each model are also listed there